[Buildroot] [git commit] board/pine64/pinecube: new board
Thomas Petazzoni
thomas.petazzoni at bootlin.com
Sat Aug 26 21:04:26 UTC 2023
commit: https://git.buildroot.net/buildroot/commit/?id=7b02ca842d5361253fe502747cdd380b67d94e47
branch: https://git.buildroot.net/buildroot/commit/?id=refs/heads/master
Add support for PineCube with:
- U-Boot 2022.04
- Linux 5.15.61
PineCube is a low-powered, open source IP camera
with the following specs:
- Allwinner S3 Cortex-A7
- 128 MiB DDR3
- 16 MiB SPI flash
- 5 MPx OV5640 camera
- MicroSD slot
- 10/100M Ethernet with passive PoE
- 802.11 b/g/n WiFi
- Bluetooth 4.1
- USB 2.0
- 26 pins GPIO header
- Microphone
- IR LEDs for night vision
Board homepage: https://www.pine64.org/cube/
Board wiki: https://wiki.pine64.org/wiki/PineCube
Signed-off-by: Jan Havran <havran.jan at email.cz>
Reviewed-by: Giulio Benetti <giulio.benetti at benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni at bootlin.com>
---
DEVELOPERS | 4 ++++
board/pine64/pinecube/extlinux.conf | 4 ++++
board/pine64/pinecube/genimage.cfg | 34 ++++++++++++++++++++++++++++
board/pine64/pinecube/post-build.sh | 5 +++++
board/pine64/pinecube/readme.txt | 31 +++++++++++++++++++++++++
configs/pine64_pinecube_defconfig | 45 +++++++++++++++++++++++++++++++++++++
6 files changed, 123 insertions(+)
diff --git a/DEVELOPERS b/DEVELOPERS
index f91c4e9a2b..241de082eb 100644
--- a/DEVELOPERS
+++ b/DEVELOPERS
@@ -1494,6 +1494,10 @@ F: board/microchip/mpfs_icicle/
F: configs/microchip_mpfs_icicle_defconfig
F: package/microchip-hss-payload-generator/
+N: Jan Havran <havran.jan at email.cz>
+F: board/pine64/pinecube/
+F: configs/pine64_pinecube_defconfig
+
N: Jan Heylen <jan.heylen at nokia.com>
F: package/opentracing-cpp/
diff --git a/board/pine64/pinecube/extlinux.conf b/board/pine64/pinecube/extlinux.conf
new file mode 100644
index 0000000000..6a18d9a2cb
--- /dev/null
+++ b/board/pine64/pinecube/extlinux.conf
@@ -0,0 +1,4 @@
+label buildroot
+ kernel /zImage
+ devicetree /sun8i-s3-pinecube.dtb
+ append console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rootwait rw
diff --git a/board/pine64/pinecube/genimage.cfg b/board/pine64/pinecube/genimage.cfg
new file mode 100644
index 0000000000..398d45e2f7
--- /dev/null
+++ b/board/pine64/pinecube/genimage.cfg
@@ -0,0 +1,34 @@
+image boot.vfat {
+ vfat {
+ files = {
+ "zImage",
+ "sun8i-s3-pinecube.dtb",
+ "extlinux"
+ }
+ }
+
+ size = 8M
+}
+
+image sdcard.img {
+ hdimage {
+ }
+
+ partition u-boot {
+ in-partition-table = "no"
+ image = "u-boot-sunxi-with-spl.bin"
+ offset = 8K
+ size = 504K # 512KB - 8KB
+ }
+
+ partition boot {
+ partition-type = 0xC
+ bootable = "true"
+ image = "boot.vfat"
+ }
+
+ partition rootfs {
+ partition-type = 0x83
+ image = "rootfs.ext4"
+ }
+}
diff --git a/board/pine64/pinecube/post-build.sh b/board/pine64/pinecube/post-build.sh
new file mode 100755
index 0000000000..8dae08a47c
--- /dev/null
+++ b/board/pine64/pinecube/post-build.sh
@@ -0,0 +1,5 @@
+#!/bin/sh
+
+BOARD_DIR="$(dirname "$0")"
+
+install -m 0644 -D "$BOARD_DIR"/extlinux.conf "$BINARIES_DIR"/extlinux/extlinux.conf
diff --git a/board/pine64/pinecube/readme.txt b/board/pine64/pinecube/readme.txt
new file mode 100644
index 0000000000..4cf6df2110
--- /dev/null
+++ b/board/pine64/pinecube/readme.txt
@@ -0,0 +1,31 @@
+Intro
+=====
+
+This directory contains a Buildroot configuration for building a
+Pine64 PineCube.
+
+Board homepage: https://www.pine64.org/cube/
+Board wiki: https://wiki.pine64.org/wiki/PineCube
+
+How to build it
+===============
+
+ $ make pine64_pinecube_defconfig
+ $ make
+
+Note: you will need access to the internet to download the required
+sources.
+
+How to write the SD card
+========================
+
+Once the build process is finished you will have an image called "sdcard.img"
+in the output/images/ directory.
+
+Copy the bootable "sdcard.img" onto an SD card with "dd":
+
+ $ sudo dd if=output/images/sdcard.img of=/dev/sdX
+ $ sudo sync
+
+Insert the micro SDcard in your PineCube and power it up. The console
+is on the serial port 2, 115200 8N1 (check Wiki for board pinout).
diff --git a/configs/pine64_pinecube_defconfig b/configs/pine64_pinecube_defconfig
new file mode 100644
index 0000000000..8f60115f8f
--- /dev/null
+++ b/configs/pine64_pinecube_defconfig
@@ -0,0 +1,45 @@
+# Target options
+BR2_arm=y
+BR2_cortex_a7=y
+BR2_ARM_FPU_VFPV4=y
+
+# Toolchain options
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_15=y
+
+# System configuration
+BR2_TARGET_GENERIC_HOSTNAME="pinecube"
+BR2_TARGET_GENERIC_ISSUE="Welcome to Pine64 Pinecube"
+BR2_SYSTEM_DHCP="eth0"
+BR2_ROOTFS_POST_BUILD_SCRIPT="board/pine64/pinecube/post-build.sh"
+BR2_ROOTFS_POST_IMAGE_SCRIPT="support/scripts/genimage.sh"
+BR2_ROOTFS_POST_SCRIPT_ARGS="-c board/pine64/pinecube/genimage.cfg"
+
+# Kernel
+BR2_LINUX_KERNEL=y
+BR2_LINUX_KERNEL_CUSTOM_VERSION=y
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.15.61"
+BR2_LINUX_KERNEL_DEFCONFIG="sunxi"
+BR2_LINUX_KERNEL_DTS_SUPPORT=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="sun8i-s3-pinecube"
+BR2_LINUX_KERNEL_NEEDS_HOST_OPENSSL=y
+
+# Filesystem
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+
+# Bootloader
+BR2_TARGET_UBOOT=y
+BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
+BR2_TARGET_UBOOT_CUSTOM_VERSION=y
+BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2022.04"
+BR2_TARGET_UBOOT_BOARD_DEFCONFIG="pinecube"
+BR2_TARGET_UBOOT_NEEDS_DTC=y
+BR2_TARGET_UBOOT_NEEDS_PYLIBFDT=y
+BR2_TARGET_UBOOT_NEEDS_OPENSSL=y
+BR2_TARGET_UBOOT_SPL=y
+BR2_TARGET_UBOOT_SPL_NAME="u-boot-sunxi-with-spl.bin"
+
+# Required host utilities for building an SDCard image
+BR2_PACKAGE_HOST_DOSFSTOOLS=y
+BR2_PACKAGE_HOST_GENIMAGE=y
+BR2_PACKAGE_HOST_MTOOLS=y
More information about the buildroot
mailing list